Sena Parani-SD1000U Manual do Utilizador

Parani-SD1000U User Guide Version 2.0.2 2012-01-18

Figure 2-2 Connecting a Serial Device to Parani-SD1000U 2.2.2. USB Driver Installation Windows XP and later versions already include the USB dr

Figure 2-3 USB Driver Installation 2.2.3. Virtual Serial Port The user can use the Parani-SD1000U adapter connected as a virtual serial port aft

3. Configuration 3.1. Operation Modes In addition to the serial port configurations the Parani-SD1000U also requires some settings for

3.2. LED Indicators Serial-Tx and Serial-Rx LED will flash accordingly when data is transmitted. For small data transmissions, it may be

When using hardware flow control, Parani-SD1000U disables RTS so that it stops receiving any further data from the host when the b

If you want to use them, to set these speeds, please configure the dipswitch to S/W Config setting and use ParaniWIN or AT commands. Please refer to P

Table 3-7 Pairing Process with other Bluetooth device by Pairing Button SD1 Status LED Other Bluetooth Device Status 1. Factory reset Mode0 Mode LED t

Figure 3-3 Main Window Figure 3-4 Information Window Serial port settings can be changed by <Start Configuration> and <Parani

Figure 3-5 Menu Bar at Upper Left corner of ParaniWIN When the ParaniWin software is able to access the Parani-SD1000U properly, the icons in the

Parani-SD1000U has 4 response messages, „OK‟, „ERROR‟, „CONNECT‟, and „DISCONNECT‟. In some cases, these responses can affect the host syst

User Guide for the Parani-SD1000U Version 2.0.2 Firmware version 2.0.X Printed in Korea Copyright Copyright 2008~2012, Sena Technologies, Inc. All ri

Figure 3-8 Signal Strength Test The signal strength test shows LInkQuality and RSSI values. The closer LinkQuality is to 255 and RSSI is to 0, thi

Figure 3-9 Connection (in) Window If the Connection Wizard icon is clicked, an easy to use pairing menu will appear: Figure 3-10 Connection Wiza

Step 1. Connect SD1 and then push the START button. Step 2. Disconnect SD1, connect SD2 and then push the Next button after setting up

start>setting>control panel>add/remove programs. For more precise details on HyperTerminal installations, please refer to Microsoft W

4. Multiple Connection Mode 4.1. Overview Parani-SD1000U supports multiple connections up to 4 slave units. There are two types of multiple connect

4.2. Configuration All the slaves should be in the status of waiting for connection either in Mode 2 or Mode 3 and the master unit tries to connect

4.3. AT Commands 4.3.1. AT+MULTI,n Select a multiple connection mode. Refer to Table 4-1 for descriptions. 4.3.2. AT+MLIST? It shows the current

4.4. Notes When large data exchange occurs in Multi-drop mode without flow-control enabled, the master unit may experience data loss. It may also ex

5. Approval Information 5.1. FCC FCC Part 15 Subpart C Section 15.247 FCC ID: S7APARANISD1000U 5.1.1. FCC Compliance Statement This device comp

6. RF Information 6.1. Radio Frequency Range 2.402~2.480GHz 6.2. Number of Frequency Channel 79 channels 6.3. Transmission Method FHSS (Frequ

Revision History Revision Date Name Description V1.0.0 2010-11-05 JH Park Initial Writing V1.0.1 2011-01-04 JH Park Modify Working Distance V2.0.2 20

Appendix A: AT Commands A.1. Terminology A.1.1. AT Command AT command set is the HTin fact standardTH HTlanguageTH for controlling H TmodemsTH. Th

Symbols Meaning ASCII Code  Carriage return 0x0D  Line feed 0x0A  Carriage return + Line feed 112233445566 Bluetooth device address N or m One d

A.3. Command Description A.3.1. ATZ Response  OK Purpose Software Reset Description This has the same effects as Powercycling the unit. This

A.3.6. AT+BTINFO? Response  112233445566,DeviceName,Mode,Status,Auth,Encryp,FlowControl  OK Purpose Display Bluetooth settings Description The

CURRENT MODE: MULTI-DROP MODE TASK1 – 000195000001 TASK2 – DISCONNECT TASK3 – DISCONNECT TASK4 – 000195000004 A.3.11. AT+BTMODE,n Response  OK P

Example AT+SETESC,42 A.3.15. ATO (ATOx, ATObdaddr) Response None Purpose Convert the operation status of „Standby‟ to „Connect‟ Description You ca

Example AT+BTSCAN,2,30 A.3.19. AT+BTSCAN112233445566,to Response  OK  CONNECT 112233445566 or  OK  ERROR Purpose Wait for connection by

Description The current Bluetooth connection will be disconnected. It takes about Supervision Timeout(S37) to detect an abnormal disconnection such as

Purpose Set authentication and data encryption Parameters Authentication=0: Inactivate (Default) Authentication=1: Activate Encryption=0: Inactivate (

Description All parameters are stored at S-register in flash memory. These values are sustained until hardware reset. A.3.32. ATSnn?  Response  v

Contents 1. Introduction 7 1.1. Overview ...

AT+BTSEC,Auth,Encr ◎ AT+BTLAST? ○ ○ AT+BTMODEn ◎ AT+BTNAME=”Name” ◎ AT+BTKEY=”nnnn” ◎ AT+BTINFO? ○ AT+BTLPM,n ◎ AT+BTSD? ○ ○ AT+BTCSD ◎

Appendix B: S-Register S-registers contain 52 parameters for the Parani-SD Series. These are stored in flash memory and the values will be saved unl

S11=1, Parani-SD allows for the escape sequence character. Whenever it is needed, the Connect status can be changed to Standby. B.7. S12: Clear Data

* When 10 bytes data are sent every intercharacter timeout, they are sent separately by 10 bytes at the optimal value. If the intercharater tim

B.23. S48: Low Power Max Interval (default 5000) This is the max interval value to use low power mode, which is set to 5000 initially. (5000 x 625μse

B.31. S59: Current Slave in Communication (default 0) This value shows the current slave number in communication. The value is automatically stored w

Appendix C: Trouble Shooting C.1. No Data Transmission C.1.1. COM Port Settings Check whether the Baud rate of Parani-SD matches that of its host

Appendix D: Parani-SD1000U mechanical drawing D.1. Parani-SD1000U mechanical drawing (mm)

Appendix E: Warranty E.1. GENERAL WARRANTY POLICY Sena Technologies, Inc. (hereinafter referred to as SENA) warrants that the Product shall conform

- Floods, lightning, earthquakes, - Water spills, - Replacement of parts due to normal wear and tear, - Hardware has been altered in any way, - Produc

A.1.2. AT Response ... 30 A.1.3. Operati

B.15. S28: Escape Sequence Character (default 43) ... 43 B.16. S31: Page Timeout (de

1. Introduction 1.1. Overview Parani-SD1000U is a usb adapter for wireless serial communication using Bluetooth 2.0

Diagnostic LED Mode, Connect, Serial Rx/Tx Environmental Operating temperature: -20 ~ 70 oC Storage temperature: -40 ~ 85 oC Humidity : 95% (Non-conde

2. Getting Started This chapter describes how to set up the Parani-SD1000U. Following items are required to get started: - One PC with USB port. - T