Sena STS Series Guia do Utilizador Página 114
- Página / 131
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
114
-----> 1
Enter Current Date (mm/dd/yy) : 02/15/03
press the ENTER key to continue
-----------------------------------------------------------------------------
RTC configuration
-----------------------------------------------------------------------------
Select menu
1. Date(mm/dd/yy) : 02/15/03
2. Time(hh:mm:ss) : 13:27:20
<ESC> Back, <ENTER> Refresh
-----> 2
Enter Current Time (hh:mm:ss) : 13:25:00
press the ENTER key to continue
-----------------------------------------------------------------------------
RTC configuration
-----------------------------------------------------------------------------
Select menu
1. Date(mm/dd/yy) : 02/15/03
2. Time(hh:mm:ss) : 13:25:01
<ESC> Back, <ENTER> Refresh
----->
Figure A-5 RTC configuration within Bootloader Menu Program
A 5.4. Hardware Test Menu
Using the Hardware test menu, the user can test hardware components. There are three hardware
test modes:
- One time
- Looping (without External test in Auto test)
- Looping (with External test in Auto test)
If the user selects One time, an auto test or each component test is performed just once. In this mode,
the ping test to the remote host (server IP address) and UART test are also performed once.
If the user selects Looping (without External test in Auto test), the auto test is performed repeatedly
until the user presses the <ctrl-c> keys. In this mode, the ping test to the remote host (server IP
address) and UART test are not performed.
Note: To perform the test on the Ethernet and UART properly, the user must connect an Ethernet
cable to the Ethernet port of the STS Series and must plug the loopback connector to all the serial
ports of the STS Series. There must exist a remote host with a valid IP address. The default server IP
address is 192.168.0.128 and it can be changed using the [Firmware Upgrade] menu. Otherwise, the
test may not be performed properly.
-----------------------------------------------------------------------------
Hardware Test
-----------------------------------------------------------------------------
- STS Series 1
- Copyright Information 2
- Trademark Information 2
- Notice to Users 2
- Technical Support 2
- Revision history 3
- Contents 4
- 5. PC Card Configuration 69 5
- 6. System Administration 74 5
- 7. System Statistics 85 5
- Appendix 8. Warranty 130 7
- 1. Introduction 8
- 1.2. Package Check List 9
- 1.3. Product Specification 9
- MAC address 10
- Session 10
- Client/Server 11
- 2. Getting Started 13
- 2.2. Connecting The Hardware 14
- 2.2.1. Connecting The Power 15
- No flow control 18
- 2.2.6. Using Remote Console 19
- 3. Network Configuration 22
- IP address 23
- Subnet mask 23
- Default gateway 23
- Primary and Secondary DNS 23
- 3.1.2. Using DHCP 24
- 3.2. SNMP Configurations 25
- sysContact: 26
- sysName: 26
- sysLocation: 26
- 3.2.4. Management Using SNMP 27
- 3.4. SMTP Configuration 29
- 3.5. IP Filtering 30
- 3.7. NFS Server Configuration 32
- 3.8. Ethernet Configuration 33
- 3.9. Web Server Configuration 33
- TCP keep-alive time: 34
- TCP “keep-alive” probes: 35
- TCP keep-alive intervals: 35
- 4. Serial Port Configuration 36
- 4.2.1. Port Enable/Disable 40
- 4.2.2. Port Title 40
- TCP mode 42
- UDP mode 42
- Modem emulation mode 42
- Serial data transfer 44
- Session disconnection 44
- TCP listening port 44
- User Authentication 45
- Telnet protocol 45
- Max. allowed connection 45
- Cyclic Connection 45
- Inactivity Timeout 46
- Socket ID 46
- TCP Nagle algorithm 47
- UDP receiving port 47
- Check the certificate CN 55
- Length 56
- Key Block(32-byte) 57
- Key (24-byte) IV(8-byte) 57
- 4.2.9. Serial Port Parameters 58
- Parity 59
- Stop bits 59
- Flow control 59
- DTR/DSR behavior 60
- Inter-character timeout 60
- 4.2.10. Modem Configuration 61
- 4.2.11. Port Logging 62
- Figure 4-18 65
- SNMP trap community 65
- 4.3. All Port Configurations 67
- Port enable/disable 68
- Port title 68
- Host mode 68
- 5. PC Card Configuration 69
- 5.1. LAN Card Configuration 70
- 6. System Administration 74
- System log buffer size 75
- 6.3. User Logged On List 76
- 6.4. Change Password 76
- 6.6. User Administration 77
- 6.7. Date And Time Settings 78
- 6.8. Configuration Management 79
- 6.9. Firmware Upgrade 80
- 6.10. User File Uploading 82
- 7. System Statistics 85
- 7.3. IP Statistics 86
- 7.4. ICMP Statistics 88
- 7.5. TCP Statistics 90
- 7.6. UDP Statistics 92
- 8. CLI guide 93
- 8.3.2. File And Disk Utils: 94
- 8.3.3. System Utilities: 94
- 8.3.4. Network Utilities: 94
- 8.7. File Transmission 96
- 8.8. Examples 96
- 9. User Customization Guide 99
- 9.3. User Defined Web Pages 100
- Appendix 1. Connections 101
- HelloDevice 102
- Remote Host 102
- RJ45-DB25 female adapter 103
- RJ45-DB25 male adapter 103
- Table A-3 Network card 104
- Table A-6 Serial Modem Card 105
- A 3.1. system.cnf 106
- A 3.2. redirect.cnf 108
- A 5.1. Overview 113
- A 5.2. Main Menu 113
- A 5.3. RTC Configuration Menu 113
- A 5.4. Hardware Test Menu 114
- A 5.5. Firmware Upgrade Menu 118
- Appendix 8. Warranty 130
Manuais e produtos relacionados com Redes Sena STS Series
Redes Sena ProBee-ZS10 Guia do Utilizador
(66 páginas)
(66 páginas)
Redes Sena PS200 Guia do Utilizador
(68 páginas)
(68 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais