Sena Parani-SD100-200 Manual do Utilizador

1Parani-SD100/200User GuideVersion 1.1.7.12011-12-26

102. Getting StartedThis chapter describes how to set up the Parani-SD Series for the first time.- 2.1 Panel Layout explains the panel layout.- 2.2 Co

11Figure Error! Style not defined.-2 The panel layout of Parani-SD2002.2. Connecting the HardwareThis section describes how to connect the Parani-SD S

122.2.2. Connecting Device to Parani-SDConnect the serial device to the Parani-SD Series as shown below.Figure Error! Style not defined.-4 Connecting

133. Configuration3.1. Operation ModesIn addition to the serial port configurations, the Parani-SD also requires includes some settings forBluetooth.

14Table 3-2 The Parani-SD LED IndicatorsIndicator Power LED Standby LED Connect LEDMode0Green ┏━━━━━ Red ┏━━━━━Mode1Green ┏━━━━━ Green (every 1 sec) ┏

153.6 Reset to Factory DefaultsTo set all the configuration settings to its factory default parameters, press the reset button, depicted inFig. 1-3. P

16blinks 3 times every 2 seconds. Keep the power ON.Step 3. Press the Pairing Button of SD2 for 2 seconds until Standby LED turns off and Connect LEDb

173.9 Software and UtilityThis configuration software and utility for firmware update is included with the product, which also canbe downloaded from h

18Figure 3-3 Main WindowFigure 3-4 Information Window

19Serial port settings can be changed by <Start Configuration> and <ParaniWIN Configuration> ofParaniWIN in the menu bar at upper left cor

2User Guide for the Parani-SD100/200Version 1.1.7.1Firmware version 1.1.XLast revised on Dec. 26, 2011Printed in KoreaCopyrightCopyright 2006~2012, Se

20SD connects to another Bluetooth device, that requires authentication, you must know the otherdevice’s Pin Code. In general, most Bluetooth devices

21Figure 3-8 Signal Strength TestThe signal strength test shows LInkQuality and RSSI values. The closer LinkQuality is to 255 andRSSI is to 0, this me

22Figure 3-9 Connection(in) WindowIf the Connection Wizard icon is clicked, an easy to use pairing menu will appear:Figure 3-10 Connection Wizard Wind

23In this example we will refer to the two Parani-SDs as SD1 and SD2 respectively. To use this menu,please do the following:Step 1. Connect SD1 and th

24Figure 3-12 HyperTerminalAttach Parani-SD to serial port of host computer and power on the Parani-SD. Check Connect LEDand Standby LEDTheir status m

254. Approval Information4.1. FCC4.1.1. FCC Compliance StatementThis device complies with part 15 of the FCC Rules. Operation is subject to the follow

265. RF Information5.1. Radio Frequency Range2.402~2.480GHz5.2. Number of Frequency Channel79 channels5.3. Transmission MethodFHSS(Frequency Hopping S

27Appendix A: ConnectionsA.1. Serial Port Pin OutsParani-SD is a DCE device compatible with the RS232 standard, a DB9 female interface.Figure A-1 Pin

28A.2. Serial Wiring DiagramA.2.1. To Host with DTE InterfaceA.2.2. To Host with DCE Interface

29Appendix B: AT CommandsB.1. TerminologyB.1.1. AT CommandAT command set is the HT in fact standardTH language for controlling modems. The AT command

3Revision HistoryRevision Date Name DescriptionV1.1.2 2007-05-26 Yh Moon Initial Revision HistoryV1.1.3 2007-09-12 Yh Moon Update Approval, Command Va

30B.1.6. SymbolsThe symbols are used for the description of command syntax as follows:Symbols Meaning ASCII CodeCarriage return 0x0DLine feed 0x0AC

31B.3. Command DescriptionB.3.1. ATZResponse OKPurposeSoftware ResetDescriptionThis has the same effects as Powercycling the unit.This command disc

32B.3.5. AT+USEDIP?Response mPurposeCheck the Baud rate set by the dip switchDescriptionm=0: Dip switches are set to ‘S/W Config’m=1: Please view t

33B.3.9. AT+BTVER?Response SD100v1.1.3 OKPurposeDisplay device firmware versionDescriptionDisplay device firmware versionReferenceAT+BTINFO?B.3.1

34Reference+++, ATOExampleAT+SETESC,42B.3.13. ATOResponseNonePurposeConvert the operation status of ‘Standby’ to ‘Connect’DescriptionYou can convert

35DescriptionFor the given to, Parani-SD is waiting for the inquiry and connection from other Bluetoothdevices. If the parameter of to is 0, it will w

36DescriptionParani-SD attempts to connect to the Bluetooth device with the given BD address. To makesuccessful connection, the Bluetooth device must

37DescriptionPin code is a string, which allows up to 16 alpha-numeric characters. Based on this pincode, Parani-SD generates a link key which is used

38DescriptionIf the authentication is activated, the pin code must be set by AT+BTKEY command. Dataencryption cannot be used when authentication is no

39B.3.31. AT&VResponse S0:m0;S1:m1; …Sn:mn OKPurposeDisplay all the S-registersDescriptionAll parameters are stored at S-register in flash me

4Contents1. Introduction 71.1. Overview ...

40ATD◎ATA112233445566◎ATA◎AT+BTSCAN◎AT+BTSCAN,n,to◎AT+BTSCAN112233445566,to◎AT+BTCANCEL○+++○AT+SETESC◎ATO●ATH●AT+BTSEC,Auth,Encr◎AT+BTLAST?○ ○AT+BTMOD

41Appendix C: S-RegisterS-registers contains 52 parameters for the Parani-SD Series. These are stored in flash memory andthe values will be saved unle

42C.7. S12: Clear Data Buffer When Disconnected (default 0)S12=0, Parani-SD does not clear the data buffer when disconnected.S12=1, Parani-SD clears t

43* When 10 bytes data are sent every intercharacter timeout, they are sent separately by 10 bytes atthe optimal value. If the intercharater timeout i

44C.24. S48: Low Power Max Interval (default 2048)This is the max interval value to use low power mode, which is set to 2048 initially. (2048 x 625μse

45Appendix D: Trouble ShootingD.1. No Data TransmissionD.1.1. COM Port SettingsCheck whether the Baud rate of Parani-SD matches that of its host equip

46Appendix E: Parani-SD100/200 mechanical drawingE.1. Parani-SD100 mechanical drawing95.3 with stub antenna16.270.0 without antenna14.30.820.5

47E.2. Parani-SD200 mechanical drawing100.8 with stub antenna16.275.3 without antenna14.30.820.5

48E.3. Parani-SD200 battery pack mechanical drawing5.268.421.0

49Appendix F: WarrantyF.1. GENERAL WARRANTY POLICYSena Technologies, Inc. (hereinafter referred to as SENA) warrants that the Product shall conform to

5B.1.3. Operation Mode...29B.1.4. Operation

50- Water spills,- Replacement of parts due to normal wear and tear,- Hardware has been altered in any way,- Product that has been exposed to repair a

6C.16. S31: Page Timeout (default 300)...43C.17. S33: Inquiry

71. Introduction1.1. OverviewParani-SD is a terminal device for wireless serial communication using Bluetooth technology that is aninternational stand

81.3. Product SpecificationParani-SD100 Parani-SD200Serial InterfaceOne female DB9 serial port for data communicationSerial speeds 1200bps to 230400bp

9Note *:Bluetooth v1.2 supports improved AFH function. AFH function is to mitigate the interferencebetween WiFi and Bluetooth radios by automatically